Low Voltage Cut Out Circuit Diagram

This circuit will detect when the voltage of a 12v battery reaches a low level. This is to prevent deep-discharge or maybe to prevent a vehicle battery becoming discharged  to a point where it will not start a vehicle. This circuit is different to anything previously presented. It has HYSTERESIS. Hysteresis is a feature where the upper and lower detection-points are separated by a gap. 

Circuit diagram :

Low Voltage Cut-Out Circuit Diagram

Normally,  the circuit will deactivate the relay when the voltage is 10v and when the load is removed. The battery voltage will rise slightly by as little as 50mV and turn the circuit ON again. This is called "Hunting." The off/on timing has been reduced by adding the 100u. But to prevent this totally from occurring, a 10R to 47R is placed in the emitter lead. The circuit will turn off at 10v but will not turn back on until 10.6v when a 33R is in the emitter. The value of this resistor and the turn-on and turn-off voltages will also depend on the resistance of the relay. 

Author : Colin Michel - Copyright : 200 Transistor Circuits

Low Cost Universal Battery Charger Schematic

Low cost solution for charging of both NiCd and NiMh batteries

Here is the schema diagram of a low cost universal charger for NiCD - NiMH batteries. This schema is Ideal for car use. It has ability to transform a mains adapter in to a charger . This one can be used to charge cellular phone, toys, portables, video batteries, MP3 players, ... and has selectable charge current. An LED is located in schema to indicate charging. Can be built on a general purpose PCB or a veroboard. I hope you really like it.

 

 A Low Cost Universal Charger Circuit Schematic

Circuit diagram:

A Low Cost Universal Charger Circuit Diagram

Parts:

R1 = 120R-0...5W
R2 = See Diagram
C1 = 220uF-35V
D1 = 1N4007
D2 = 3mm. LED
Q1 = BD135
J1 = DC Input Socket

Specifications:

• Ideal for in car use.
• LED charge indication.
• Selectable charge current.
• Charges Ni Cd or NiMH batteries.
• Transforms a mains adapter into a charger.
• Charge cellular phone, toys, portables, video batteries …

Features:

• LED function indication.
• Power supply polarity protected.
• Supply current: same as charge current.
• Supply voltage: from 6.5VDC to 21VDC (depending on used battery)
• Charge current (±20%): 50mA, 100mA, 200mA, 300mA, 400mA. (selectable)

Determining the supply voltage:

This table indicates the minimum and maximum voltages to supply the charger. See supply voltage selection chart below.

Example:

To charge a 6V battery a minimum supply voltage of 12V is needed, the maximum voltage is then 15V.

Voltage selection:

Voltage Selection Chart For Low Cost Universal Battery Charger

Determining the charge current:

Before building the schema, you must determinate how much current will be used to charge the battery or battery pack. It is advisable to charge the battery with a current that is 10 times smaller then the battery capacity, and to charge it for about 15 hours. If you double the charge current , then you can charge the battery in half the time. Charge current selection chart is located in diagram.

Example:

A battery pack of 6V / 1000mAh can be charged with 100mA during 15 hours. If you want to charge faster, then a charge current of 200mA can be used for about 7 hours.

Caution:

The higher charge current, the more critical the charge time must be checked. When faster charging is used, it is advisable to discharge the battery completely before charging. Using a charge current of 1/10 of the capacity will expand the lifetime of the battery. The charge time can easily be doubled without damaging the battery.

Note:

• Mount the transistor together with the heatsink on the PCB, bend the leads as necessary. Take care that the metal back of the transistor touches the heatsink. Check that the leads of the transistor do not touch the heatsink.